0102030405
High-Quality Eaton Vickers V-Series Equivalent Hydraulic Vane Pump Cartridges from China Suppliers and Factory
Model Designation
| (F3-) | PC- | 25V | 19 | R | 10 |
| Note | Cartridge mark | Series | Flow code | Rotation | Design number |
| No-marking: Petroleum series oil emulsification fluid water glycol-fluid F3: phosphate ester fluid |
PC-Cartridge kit of single pump double pump shaft end PCT-Cartridge kit of double pump cover end |
20V | 2,3,4,5,6,7,8,9, 10,11,12,14 | (Viewed from shaft end of pump) L-Left hand for counter clockwise R-Right hand for clockwise |
10 |
| 25V | 10,12,14,15,17, 19,21,25 | ||||
| 35V | 21,25,30,32,35, 38,45 | ||||
| 45V | 42,45,50,57,60, 66,75 |
USgpm Flow(USgpm) at 1200r/min and 0.69MPa.
The data of relevant series, model are unanimous. Please see V series-single pump data.
Technical Data
| NO | Part | Qty | NO | Part | Qty | NO | Part | Qty |
| 1 | Pin | 2 | 5 | cam ring | 1 | 9 | Retainer | 1 |
| 2 | sliding bearing | 1 | 6 | vane kit | 12 | 10 | Oring | 1 |
| 3 | cross pan head bolts | 2 | 7 | Rotor | 1 | 11 | Retainer | 1 |
| 4 | inlet support plate | 1 | 8 | outlet support plate | 1 |
| Series | φA | B | C | φD | E | φF | φG | H | K | M(Gasket) | N(O-Ring) |
| 20V | 82.55 | 81.5 | 70.1 | 47 | 61.5 | 4.8 | 76.2 | 7 | 73.6 | 82.76x76.26×3.5 | 40x3.55 |
| 25V | 96.8 | 98.8 | 87 | 52.2 | 71.2 | 4.8 | 90.5 | 7 | 88.19 | 97x91x3.5 | 44×3.53 |
| 35V | 114.3 | 117.7 | 105 | 72.2 | 90.3 | 6.4 | 108 | 8 | 103.94 | 114.5x108.5x3.5 | 63.09x3.53 |
| 45V | 133.35 | 141.1 | 129.6 | 80.2 | 105.5 | 6.4 | 127 | 8 | 123.8 | 133.6x127.6x3.5 | 71x3.55 |
| Series | Inside spline tooth outline parameter of rotor | ||||
| Number of teeth | Pitch | Pressure angle | Major Diameter | Minor Diameter | |
| 20V | 30 | 48/96 | 45° | 16.617 | 15.56 |
| 25V | 40 | 48/96 | 45° | 21.9 | 20.86 |
| 35V | 37 | 40/80 | 45° | 24.38 | 23.10 |
| 45V | 14 | 12/24 | 30° | 32.59 | 27.6 |
Frequently Asked Questions (FAQ)
What are the V Series equivalent cartridge kits used for?
These cartridge kits are designed as direct replacements for Eaton Vickers V Series single and double vane pumps (including 20V, 25V, 35V, and 45V). They allow quick and cost-effective rebuilding of hydraulic pumps without replacing the entire housing.
Are these equivalent cartridge kits fully interchangeable with OEM parts?
Yes, our cartridge kits are manufactured to the same dimensions, tolerances, and performance specifications as original Eaton Vickers parts, ensuring complete interchangeability and seamless installation.
How do I choose the correct rotation (L or R) for my cartridge kit?
The rotation is determined by viewing the pump from the shaft end. "R" designates right-hand (clockwise) rotation, while "L" designates left-hand (counter-clockwise) rotation. Be sure to verify your system requirements before ordering.
What hydraulic fluid compatibility is offered?
Standard cartridge kits (no prefix) are compatible with petroleum-based oils, emulsification fluids, and water glycol-fluids. For phosphate ester fluids, please specify the "F3" prefix designation when ordering.
What components are included in a standard PC/PCT cartridge kit?
A complete cartridge kit typically includes the pins, sliding bearing, cross pan head bolts, inlet support plate, cam ring, vane kit (12 vanes), rotor, outlet support plate, retainers, and corresponding O-rings.
What does the flow code refer to in the model designation?
The flow code represents the nominal flow rate in US gallons per minute (USgpm) measured at a standard speed of 1200 r/min and a pressure of 0.69 MPa. Refer to the model designation table to match your required flow code with the specific pump series.